Welcome to the RANDOMACC Autopsy Cart Pages

MEDICAL, PATHOLOGY and MORTUARY EQUIPMENT

Designed with safety and ease of use in mind. This Autopsy table shown below is our Standard Tilting-Elevating Autopsy table. In any and all configurations it is made to easily cater for the heavy loads. Loads of 350kg are not a problem for this cart. It has a handy easily operated hand control to raise and lower and tilt the tray. The tray may be tilted 15deg (550mm , 22" ) slope to either end. A drain with plug and bucket hook is at one end.However it can be set up to suit your requirements it can be a Cadaver Cart / Patient Carrier or Covered Cadaver Carrier. We can also supply it as a Down-Drafted Dissection table with perforated grid plates and with an extraction duct, ready for connection to the buildings ventilation system. To aid the removal of noxious vapors down and away from the user.

The RANDOMACC TILTING-ELEVATING AUTOPSY TABLE Model AT350k is made to assist and enable the easy handling of the larger bodies so often now encountered. The sloping edge of the standard sizedremovable body tray makes it easier for the body transfer. The tray size is 2060mm (81"0) x 760mm (30") The AT350k with its Electromechanical hoisting system will effortlessly raise, lower and transport cadavers of 350 kg (770lb). Making a some times very difficult job safe and easy. The AT350k has its own battery and charging system. The 12-volt motorized linear actuators provide Safety with Electromechanical hoisting. The tray sub frame is fitted with strong corner buffers and the white fiberglass chassis cowl protects the electronics and makes wash down a breeze.

The AT350k Elevating Tilting Table can be supplied in many different configurations to suit many different requirements,

Standard Autopsy Cart AT350k

Covered Cadaver Carrier AT350kCCC

Dissection Table with Downdraft AT350kDDd

It has a lot of options, as shown it can be used as a:-

Height adjustable Autopsy table.

Heavy load hospital cart. Covered Cadaver Carrier with lightweight cover frame.

Embalming Cart

Or if you require something special:-
Its top can be compatible with a fork hoist.
It can be fitted with roller top and roller body trays.
We are able to make the cart top to suit YOUR specific needs. The table can be elevated to give a work top height of 1080mm (42 1/2") or lowered down to 780mm (30 3/4") or anywhere in between.

The AT350k shown here has the optional (Extra) side rails fitted

There are no pedals to pump, to raise,lower or tilt just a finger touch is all that is required, both ends may be raised at once or seperatly. The tray may be tilted to either end.

Construction:- The only metal used in the construction of our carts is STAINLESS STEEL.
All moving components are fully covered, wash down is a breeze.
Safe easy maneuverability.
The AT350k is fitted with heavy-duty 8” (200mm) swivel casters with central and directional
lock. The casters have precision ball bearings in the swivel head, as well as precision ball
bearings in the wheels. The wheel tread is made of non-marking Polyurethane.
Directional lock on 1 caster makes the trolley very easy to maneuver.
3 position single lever braking system means that one wheel can be locked in the straight-ahead position,
while the other 3 casters pivot. This gives very good control for when maneuvering the cart through hospital hallways and doors.
There is a brake lever at each end of the cart, with the foot push the lever down one way and the
directional lock is applied to one caster, this is used when the cart is maneuvered through wards and doorways.
Press the lever to the central position and all casters roll and rotate freely, in this position the cart can be pushed in any direction.
Press the lever down the other way and all casters have full lock applied.

We also make and supply a range of standard Autopsy tables and Carts, the model shown here is our ATE, 0ne end of the table may be easily raised for better drainage.

This series of carts can be supplied as

ATE as shown here
2CS2T 2 cadaver litter
2CFH2T Fork lift compatable 2 Cadaver litter
BTS Autopsy cart saddle type Autopsy cart .

March 2008 B.S.Industries Tel: 0064 9 4385359 Fax: 0064 9 4385359 Email: barrie@randomacc.co.nz HOME